Back to Articles

Regulatory guidance · November 2026

LNAPL remediation regulations: How to identify the requirements for your site

By

Nelson Staff

, Nelson Team

November 19, 2026

TL;DR

LNAPL remediation requirements depend on the site and jurisdiction. Identify the regulator and reporting trigger at discovery. Address any immediate source control in parallel with required notification.

Assess free product and its effects. Use field evidence to establish where the product is and whether it is migrating or sustaining a plume. A single well reading can miss residual product.

Confirm the closure requirements. Document the applicable free-product endpoint and what the regulator expects to see before closing the file.

Finding petroleum product in a monitoring well can change a project overnight. It may trigger reporting or immediate response. It can also change what the regulator expects from the investigation and what the owner must demonstrate before the file can close. Start by identifying who regulates the activity that caused the release, then check what the governing rules and approvals require for the product itself. Soil and groundwater criteria are only part of that review.

LNAPL stands for light non-aqueous phase liquid. Gasoline, diesel and other petroleum products can occur as a separate phase in the subsurface. Some product may enter a monitoring well. Some can remain trapped in soil pores and still release dissolved constituents to groundwater or vapours into soil gas. These conditions can coexist, so an investigation needs to establish how the product is behaving as well as what contaminants are present. A well with no visible product on one visit can still be near residual LNAPL. Interpret well readings alongside the soil profile and seasonal groundwater data. [1]

Identify who regulates the release and what decision you need

Start with the activity and location. A release at an operating pipeline, a former retail fuel outlet and a federal property can follow different processes even when the product is diesel in all three cases. Record the source, the operator, the affected parcels and any applicable licences, approvals or orders. If product or contaminated groundwater has crossed the property line, identify the landowners and potential receptors. Check whether the site’s circumstances bring in additional authorities or notification duties.

In Alberta, the Alberta Energy Regulator (AER) publishes release reporting and contamination management requirements for activities it regulates. For a non-energy facility or brownfield, start with Alberta Environment and Protected Areas’ contaminated-site guidance and confirm who administers the file. A project on federal property may also have federal departmental requirements. A redevelopment approval and a spill-response file can create separate obligations, so record what each authority expects and which written outcome the owner needs. [2], [3], [4], [8]

For each requirement, keep the supporting document or regulator correspondence in the project file. If a project changes hands, the next owner should be able to see which obligations come from legislation, which come from an approval or order and which were agreed for the site. That record also helps the consultant write a scope that covers the actual regulatory decision.

Check reporting at discovery

Establish the applicable reporting trigger, who must notify whom and when the written follow-up is due. Triggers may depend on adverse effects, volume, the receiving environment or a condition in an operating approval. Check who needs notice beyond the primary regulator, including potentially affected parties where required. Record the date and time of discovery, the observed conditions, any immediate actions and the information still being confirmed. A historical release discovered during drilling can raise reporting duties even if the original spill date is unknown. [2], [3]

For AER-regulated sites, Manual 021 explains that under section 110 of Alberta’s Environmental Protection and Enhancement Act, a release that may cause, is causing or has caused an adverse effect must be reported as soon as the person knows or ought to know of the release. For an energy-development release, the AER lists its 24-hour reporting line and requires a written release report after notification. Check the applicable rule and approval for the deadline and any separate notices to affected parties. Document what is known now rather than holding a required notification until lab results arrive. Where there is an ongoing leak or an immediate threat, address source control and protection of affected people or water supplies in parallel with reporting. [2], [3]

Where Alberta’s Remediation Regulation applies, plan for the reporting that follows initial notification. The AER directs operators to submit an environmental site assessment or remediation report with a Record of Site Condition, as applicable. If it becomes clear that remediation cannot be completed within two years of when the person responsible became aware, or ought to have become aware, of the release, the remedial action plan is due immediately. A release beneath operating infrastructure is an example where this can be clear early. [3], [9]

Assess the free product as well as its effects

Build the investigation around a conceptual site model. Locate the likely source and map the product footprint. Determine what soil layers or buried features can carry it, and where groundwater or vapour could reach a receptor. The work may include measuring product and water levels in suitable wells over time, assessing soil cores, and sampling groundwater or soil gas where the pathways warrant it. Define the separate-phase footprint separately from the dissolved plume, which can extend beyond it. Use the findings to decide whether the separate phase is migrating or recoverable and whether it is sustaining a dissolved plume or a vapour concern. [1], [3]

An apparent product thickness measured in a well describes what is in the well at that time. The thickness can change with water levels and soil conditions. On its own, it cannot establish how much product is in the formation, how far it extends or whether pumping will recover it effectively. Where hydraulic recovery is being considered, LNAPL transmissivity can help assess how readily the product moves through the formation into a well. Use that evidence to design or evaluate recovery. Confirm with the regulator what measurements it expects and how it will use them. [1], [5]

For an AER-regulated project, Manual 021 identifies removing free fluids as one example of initial source control. It identifies known or suspected non-aqueous phase liquid as a circumstance where the AER expects additional detail when a remedial action plan is submitted. Manual 021 also calls for removing or controlling sources as soon as practicable, including when concentrations are below applicable Tier 1 or Tier 2 values. If transfer to a neighbouring property, surface water or a building is plausible, reflect that in the sampling design and proposed response. A well network chosen purely for convenient access may miss exactly the pathway the regulator wants resolved. [3]

Agree on measurable remediation objectives

Write objectives for source control, remaining product and the relevant exposure pathways. An objective might specify how the team will demonstrate that a leak has stopped or that the LNAPL footprint is stable. Other objectives may call for defined recovery performance, groundwater results at designated locations or evidence that vapour risks are controlled. For every objective, agree on the measurement, its location and how long the condition must hold. If a recovery system will be turned off, establish what rebound monitoring will be used to assess whether the result persists. [1], [3], [5]

Ask the regulator what free-product endpoint applies to the intended decision. Confirm whether rules require absence of evidence of free product, whether any residual product can remain under an accepted approach and what evidence is needed to change or stop active recovery. Keep that regulatory decision separate from the recovery system’s performance. Low recovery rates or transmissivity may inform how you operate a system, while the applicable closure requirements still determine whether the remaining source and its effects have been addressed. Ontario offers a specific example. Under section 49(1) of Ontario Regulation 153/04, a property meets an applicable site condition standard for a petroleum hydrocarbon only if the qualified person determines there is no evidence of free product. The provision identifies visible petroleum film or sheen in groundwater or surface water, or in samples of either, among the possible evidence. That is a requirement within Ontario’s record-of-site-condition framework. [1], [6]

Build the closure file while the work is underway

Agree early on what the final submission must contain. A closure package typically needs the release and notification history, the conceptual site model, delineation maps and the evidence that each objective has been met. Include field records and validated laboratory results, recovery volumes and their measurement basis, and records showing where recovered product, water or excavated material went. If a closure decision depends on monitoring or land-use controls, document the conditions and who will maintain them. [3], [7]

In Alberta, determine whether the owner needs a voluntary remediation certificate. A limited certificate covers a defined area and a site-based certificate covers the entire site. For an AER project, follow its Record of Site Condition and submission requirements. The Record of Site Condition documents the work and site status. Apply for the applicable closure instrument separately if the project calls for one, and confirm its geographic scope. [3], [7], [9]

A useful first meeting with the regulator ends with answers the project team can build into its scope. Confirm when and how to report, how to investigate the product, what endpoint applies and which records will support closure. If the file changes after that meeting, record the decision and update the scope while there is still time to collect the evidence.

References

Interstate Technology & Regulatory Council, LNAPL Site Management, Key LNAPL Concepts https://lnapl-3.itrcweb.org/3-key-lnapl-concepts/

Alberta Energy Regulator, Release Reporting Requirements https://www.aer.ca/regulations-and-compliance-enforcement/release-reporting-requirements

Alberta Energy Regulator, Manual 021 Contamination Management https://static.aer.ca/prd/documents/manuals/Manual021.pdf

Government of Alberta, Contaminant management https://www.alberta.ca/contaminant-management

Interstate Technology & Regulatory Council, LNAPL Site Management, Transmissivity appendix https://lnapl-3.itrcweb.org/appendix-c-transmissivity-tn-appendix/

Government of Ontario, Ontario Regulation 153/04, section 49 https://www.ontario.ca/laws/regulation/r04153

Government of Alberta, Regulatory closure https://www.alberta.ca/part-four-regulatory-closure

Environment and Climate Change Canada, Federal Contaminated Sites Action Plan Decision-Making Framework https://www.canada.ca/en/environment-climate-change/services/federal-contaminated-sites/publications/decision-making-framework-version-4-1.html

Alberta Energy Regulator, Remediation Regulation Administration, remedial action plans and submissions https://www.aer.ca/regulations-and-compliance-enforcement/site-closure-requirements/remediation/remediation-regulation-administration

Read Next

Regulatory guidance•2026-11-19Alberta Tier 1 soil and groundwater remediation guidelines: How to assess their applicability

Mobile thermal technology•2026Mobile thermal technology: configured for the material, brought to site

US remediation•2026Petroleum-contaminated soil treatment in the US: build the plan around the fuel profile

Back to Articles Main Page

Stay Informed

Get Nelson updates in your inbox

Project milestones, regulatory developments, and technical briefs. One email at a time. No noise.

Read Next

  • Alberta Tier 1 soil and groundwater remediation guidelines: How to assess their applicability
  • Mobile thermal technology: configured for the material, brought to site
  • Petroleum-contaminated soil treatment in the US: build the plan around the fuel profile

More from Nelson

  • PFAS and the changing landscape: What site owners should know
  • Alberta Tier 1 soil and groundwater remediation guidelines: How to assess their applicability
  • Mobile thermal technology: configured for the material, brought to site
  • How to use The Hub for contamination research
  • Navigator: a practical guide to remediation strategy
  • The Ground Truth: Warren Nelson's remediation newsletter
  • A new era of enlightenment
  • Value should be the final outcome
  • What’s next at Nelson
  • Why independent research matters more than anything
  • Over thirty years of permanent outcomes: a field review of Nelson’s project record
  • Petroleum-contaminated soil treatment in the US: build the plan around the fuel profile

Site Navigation

  • All Articles & Research
  • Thermal Remediation Capabilities
  • Project Case Studies
  • Remediation Glossary
  • About Nelson Environmental Remediation
  • Contact Nelson